Peracetic acid pretreatment of sugarcane bagasse for enzymatic hydrolysis: a continued work

Previous work has shown that the enzymatic hydrolysis of sugarcane bagasse could be greatly enhanced by peracetic acid (PAA) pretreatment. There are several factors affecting the enzymatic digestibility of the biomass, including lignin and hemicelluloses content, cellulose crystallinity, acetyl group content, accessible surface area and so on. The objective of this work is to analyze the mechanism of the enhancement of enzymatic digestibility caused by PAA pretreatment. Delignification resulted in an increase of the surface area and reduction of the irreversible absorption of cellulase, which helped to increase the enzymatic digestibility. The Fourier transform infrared (FTIR) spectrum showed that the absorption peaks of aromatic skeletal vibrations were weakened or disappeared after PAA pretreatment. However, the infrared crystallization index (N.O'KI) was increased. X‐ray diffraction (XRD) analysis indicated that the crystallinity of PAA‐treated samples was increased owing to the partial removal of amorphous lignin and hemicelluloses and probable physical change of cellulose. The effect of acetyl group content on enzymatic digestibility is negligible compared with the degree of delignification and crystallinity. The results indicate that enhancement of enzymatic digestibility of sugarcane bagasse by PAA pretreatment is achieved mainly by delignification and an increase in the surface area and exposure of cellulose fibers. Copyright © 2008 Society of Chemical Industry     

.NET组件和COM组件的应用集合研究

组件对象模型（COM）为代码的重用性提供了一种模块化和面向对象的技术标准。.NET组件是微软公司在 .NET平台上发布的新一代组件模型。文中介绍了 .NET组件和COM组件的互操作性以及 .NET组件的原理和体系结构，并以手机接口平台为技术背景，讨论了如何在两个不同平台上对COM和 .NET组件进行融合，针对此类应用提出了系统设计、体系结构和功能构成等应用方案，较详细地讨论了在非 .NET平台上调用.NET组件。     

Two-dimensional symmetric multimode interferences in silicon square waveguides

Symmetric interference in two-dimensional multimode silicon waveguides is experimentally investigated. For a 100/spl times/100 /spl mu/m/sup 2/ cross section, 2700-/spl mu/m-long waveguide fabricated on silicon-on-insulator substrate, an 8/spl times/8 matrix of replicated images with high contrast ratio is demonstrated for 1530-1570 nm wavelength range. Symmetric interference results in reduced device length, and the actual device length is consistent with the theoretical expectation. The device also exhibits stable imaging in terms of good loss uniformity, and low wavelength and polarization dependencies among the replicated images.     

IF钢冷轧及再结晶初期微观组织的TEM研究

采用透射电子显微镜对不同压下量和再结晶初期的IF钢样品进行了研究．结果表明：无论是在较小形变量下还是在较大形变量下，形变不均匀性是普遍存在的；冷变形程度不同，织构组分不同，TEM形貌也不同；在再结晶的最初期，冷轧的形变组织演变为近乎等轴的亚晶，优先形成{111}〈uvw〉取向的晶核，晶核逐渐吞并周围的形变基体而长大，最终形成再结晶γ-纤维织构．     

Local residence time,residence revolution,and residence volume distributions in twin‐screw extruders

This work was aimed at studying the overall, partial, and local residence time distributions (RTD); overall, partial and local residence revolution distributions (RRD) and overall, partial and local residence volume distributions (RVD) in a co‐rotating twin screw extruder, on the one hand; and establishing the relationships among them, on the other hand. Emphasis was placed on the effects of the type and geometry of mixing elements (a gear block and various types of kneading elements differing in staggering angle) and process parameters on the RTD, RRD and RVD. The overall and partial RTD were directly measured in‐line during the extrusion process and the local ones were calculated by deconvolution based on a statistical theory. The local RTD allowed comparing the mixing performance of mixing elements. Also it was confirmed both experimentally and theoretically that specific throughput, defined as a ratio of throughput (Q) over screw speed (N), controlled all the above three types of residence distributions, be they local, partial or overall. The RRD and RVD do not provide more information on an extrusion process than the corresponding RTD. Rather they are different ways of representing the same phenomena. POLYM. ENG. SCI., 48:19–28, 2008. © 2007 Society of Plastics Engineers     

企业以顾客为中心的营销策略过程研究

试图构建企业以顾客为中心的营销策略过程的一般模型，并利用已有的研究成果对其构成要素进行了深入分析．在此基础上，对此模型所形成的企业营销策略循环进行分类分析，并以实例说明它们所代表的现实意义，从而为企业的决策提供帮助．     

One-to-Many and Many-to-One Optical Chaos Communications Using Semiconductor Lasers

A theoretical construction of one-to-many (OTM) and many-to-one (MTO) chaos synchronization communications using semiconductor lasers is presented. One center laser provides strong injections (strong link) to other side lasers, and the side lasers also provide weak injections (weak link) to the center one. Simulation results show that the side lasers synchronize with the center laser through injection-locking. In addition, messages transmitted via the strong links or the weak links experience strong chaos pass filtering, enabling us to realize OTM and MTO communications.     

便携式全站仪在钻采井架钢结构安装中的应用

文章介绍了一种由便携机和全站仪组成的便携式全站仪 ,阐述了该全站仪在钻采井架钢结构施工安装过程中的测量工作 ,对测点产生的误差采用伪逆自由网平差方法进行处理 ,控制点的精度可达到± 5mm ,该全站仪具有快速、灵活、准确的特点 ,不仅提高了生产效率 ,而且达到了对资料的计算机化管理。